Troubleshooting

Pod Not Firing? Work Through These 7 Checks in Order

You press the button, or take a draw, and nothing happens. No vapour, no crackle, maybe a light that blinks at you once and gives up.

Work through these seven checks in order. They’re arranged so that the most common and cheapest fixes come first — most people find their answer in the first three.

1. Is it actually charged?

Obvious, and still the single most common cause. A device at 5% will often flash rather than fire, because the chip won’t deliver power it doesn’t have.

Plug it in for thirty minutes with a cable you know works, and watch the indicator. If nothing lights up at all when connected, the problem is the port or the cable, not the battery.

While you’re there: shine a light into the USB-C port. Pocket lint packed into the back of the connector is extremely common and blocks charging completely. Fish it out with a wooden toothpick — never metal, and never a pin.

2. Is the pod seated properly?

Pods need a firm push to make contact. A pod that’s sat a millimetre high looks fine and does nothing.

Remove it, look at the two metal contacts on the bottom of the pod and the two pins inside the device. Push it back in until it stops. Some devices give an audible click; most don’t, so push until you feel resistance end rather than until it feels “in”.

3. Are the contacts clean?

This is the one people skip, and it solves a huge share of “dead device” cases.

Condensation and liquid residue form a film on the contact pins. That film is enough to break the circuit. Take a dry cotton bud, wipe the pins inside the device and the contacts on the pod, and leave both to dry for a minute before reassembling.

If there’s visible crust, a cotton bud very lightly dampened with isopropyl alcohol will shift it — but make sure everything is completely dry before you put the pod back. Alcohol and a live coil are not a good combination.

4. Is the device locked?

Most button-activated pod devices have a child-lock: five rapid clicks toggles between locked and unlocked. It’s designed to stop accidental firing in a pocket, and it’s easy to trigger by accident.

Click five times quickly and try again. If your device has a screen, check whether it shows a padlock icon.

5. What is the light telling you?

The blink pattern is diagnostic, not decorative. Exact codes differ between brands and models — always check your manual — but the patterns fall into a few families:

Pattern Usually means What to try
Blinking while charging, then solid Normal charging cycle Nothing — let it finish
Three quick blinks on each press No atomiser detected, or a short circuit Reseat and clean the pod; try a different pod
Five blinks, then dead Battery flat or protection triggered Charge for 30 minutes
Continuous flashing after charging Contact fault or a dead coil Clean contacts, replace the pod

If your device shows a colour rather than a count, the usual convention is green for charged, blue or white for mid, red for low. Again — check the manual, because this isn’t universal.

6. Is it a coil or resistance error?

If your device has a screen and it says something like “no atomiser”, “check atomiser” or “short circuit”, the pod is the problem, not the battery.

Three likely reasons: the coil wire has snapped (a dead coil), liquid has got into the connector and is shorting the pins, or the pod’s resistance is outside what the device will accept. Try a different pod. If a new pod works immediately, you’ve found it — and the old one goes in the bin, not the drawer.

7. Is the auto-draw sensor blocked?

Buttonless devices fire when a sensor detects air moving through the airway. Liquid in that airway — usually from overfilling, or from someone blowing into the mouthpiece to “clear” a gurgle — kills the sensor’s ability to detect a draw.

The symptom is distinctive: the device lights up when you charge it and responds to nothing else. There’s no reliable user fix. If the device is under warranty, contact us — this is a defect case, not wear and tear.

When the device is genuinely finished

Some failures aren’t fixable:

  • Water damage. Dropped in water, or stored in a steamy bathroom for months.
  • Battery degradation. After 12–18 months of daily charging, capacity drops to the point where the device can’t sustain a draw.
  • Charging port failure. Usually from cable strain rather than the port itself wearing out.
  • A hard drop. Internal solder joints fail before the case does.

If the device is under two years old and failed through normal use — not a drop into a sink — it may be a warranty case. Send us your order number and a short description, and we’ll tell you where you stand.

Keeping the next one alive

  1. Charge with the cable it came with, or a reputable one — cheap cables are a common cause of port damage
  2. Don’t leave it on charge overnight, every night
  3. Wipe the contacts once a week when you refill
  4. Don’t store it in the bathroom — humidity is the quiet killer
  5. Don’t blow into the mouthpiece, ever

Most pod devices that “die” have done nothing of the sort. They’ve got a dirty contact, a flat battery, or a pod that isn’t quite in. Ten minutes of methodical checking saves a replacement — and if it turns out you do need one, the shop is right there.

Need the pods for this?

Shipped from Rotterdam. Order before 15:00 CET for same-day dispatch.

Shop now

Read next

Troubleshooting

Vape Leaking From the Bottom? Here’s What’s Actually Happening

You take the pod out, and there’s a ring of liquid sitting on the contact pins. Your hand…

November 19, 2026 · 5 min read
Troubleshooting

Why Your Vape Tastes Burnt — and 6 Fixes That Actually Work

Burnt taste from a new pod is almost never a faulty coil. Here are the six real causes,…

November 19, 2026 · 5 min read