Troubleshooting

Why Your Vape Tastes Burnt — and 6 Fixes That Actually Work

You filled a fresh pod, waited a few minutes, took a draw, and got a mouthful of scorched cotton. It tastes like a bonfire and it lingers for the rest of the day.

The instinct is to blame the pod. In practice, a genuinely faulty coil is rare — maybe one in fifty. The other forty-nine times, something happened between filling the pod and taking that first puff.

Here are the six causes, in the order they’re actually the problem, plus how to tell which one you’ve got.

First, work out which kind of “burnt” you have

People use one word for three different problems, and they have different fixes:

Symptom What it is Recoverable?
Sharp, acrid hit that catches the back of your throat Dry hit — the cotton is dry and the coil is overheating Yes, if you stop immediately
Burnt taste that stays in your mouth after the puff ends Scorched cotton No — the pod is finished
Sweet or bitter taste that gets worse over days Caramelised liquid on the coil Partially — lower the wattage, or replace

That middle row is the one people miss. Once cotton is scorched, the burnt compounds are bonded to it. No amount of resting, refilling or shaking will remove them. If your pod tastes burnt even when it’s full and cold, it’s done.

1. The coil was never primed

This is the most common cause by a wide margin, and it happens in the first thirty seconds of ownership.

A new pod’s cotton is bone dry. When you fill it, the liquid has to physically soak through the wicking material to reach the coil — that takes time, not a quick swirl. Fill the pod, then wait five to ten minutes. If you’re impatient, take two or three dry pulls (mouth only, don’t press the button and don’t inhale into your lungs) to pull liquid down the wick faster.

Then start at the lowest wattage your device allows and work up over the first twenty puffs. Firing a dry coil for even two seconds at full power is enough to permanently scorch the cotton.

2. Your wattage is too high for the coil

Every coil has a power range it was designed for. Push past it and the coil outruns the wick’s ability to keep up — the cotton goes dry mid-puff and burns.

Coil resistance Typical comfort range Draw style
0.4 Ω 20–30 W Direct to lung
0.6 Ω 18–25 W Restricted direct to lung
0.8 Ω 12–18 W Mouth to lung
1.0 Ω and above 10–14 W Mouth to lung

These are ranges, not rules — always check what your device or the pod packaging recommends. But if you’ve put a 1.0 Ω pod in and left the wattage at 30 W from your last coil, that’s your answer.

3. You’re vaping faster than the cotton can re-wick

Cotton is a sponge, not a pipe. After each puff it needs a few seconds to pull fresh liquid back to the coil. Chain-vape six draws back to back and the fourth or fifth will run dry — even in a perfectly primed pod at the right wattage.

If you vape heavily, take three or four puffs, then set the device down for thirty seconds. Thick, high-VG liquids make this worse because they move through cotton more slowly.

4. The pod is running dry

Below the wicking ports, the coil has nothing to draw from. It’s obvious when a pod is empty, but the dangerous zone is the last fifth — the liquid is still visible, sloshing around the bottom, but it isn’t reaching the cotton.

Refill when the level drops to the bottom third. If you’re caught short, tilt the device so liquid runs toward the wicking ports between puffs.

5. Your liquid is caramelising on the coil

Sweeteners — particularly sucralose, which is in a lot of dessert and fruit liquids — don’t fully vaporise. They cook onto the coil as a dark residue. Once that layer builds up, every puff tastes slightly burnt no matter how careful you are.

You can slow this down by running 10–15% below the coil’s maximum wattage and avoiding very dark liquids. You can’t stop it. A pod used daily on a sweet liquid will need replacing in two to three weeks; a clear, lightly sweetened liquid in the same pod might last four.

6. The liquid is too thick for the pod

Pod systems are generally built around a 50/50 VG/PG ratio. High-VG liquids (70% and above) are noticeably thicker and wick more slowly, which produces dry hits and weak flavour — usually not leaking, which is how you tell it apart from overfilling.

If you want to use a high-VG liquid, you need a device with larger wicking ports. If you’re using a slim pod, stay near 50/50.

When it really is the pod

Occasionally a coil is dead on arrival — a manufacturing defect in the wire or the cotton packing. The tell is simple: you primed it properly, waited ten minutes, started at low power, and the very first puff tasted burnt.

That’s a warranty case, not user error. Contact us with your order number and a short description of what happened — we replace faulty pods, and you don’t pay return shipping.

The five-step routine that prevents it

  1. Fill the pod and wait ten minutes before the first puff
  2. Start at the lowest wattage, work up over twenty puffs
  3. Refill at the bottom third, never vape it dry
  4. Pause a few seconds between puffs
  5. Replace the pod every two to three weeks, or sooner if flavour drops

None of this is complicated, but all five have to happen together. Skip the priming and the rest doesn’t matter.

If you’ve worked through all six causes and it’s still burning, something doesn’t match — usually the pod and the device. Check the compatibility table to confirm the pod is actually rated for your device, or send us a message with the device name and we’ll check for you.

Need the pods for this?

Shipped from Rotterdam. Order before 15:00 CET for same-day dispatch.

Shop now

Read next

Troubleshooting

Pod Not Firing? Work Through These 7 Checks in Order

You press the button, or take a draw, and nothing happens. No vapour, no crackle, maybe a light…

November 19, 2026 · 5 min read
Troubleshooting

Vape Leaking From the Bottom? Here’s What’s Actually Happening

You take the pod out, and there’s a ring of liquid sitting on the contact pins. Your hand…

November 19, 2026 · 5 min read