Troubleshooting

Vape Leaking From the Bottom? Here’s What’s Actually Happening

You take the pod out, and there’s a ring of liquid sitting on the contact pins. Your hand is sticky. You’ve probably already lost a bit of liquid into a pocket or a bag.

Before you replace anything, do one test — because roughly half the people who think their pod is leaking are looking at condensation, and the fixes are completely different.

First: is it actually leaking?

Dry the base of the pod and the inside of the device thoroughly with a tissue. Vape five or six puffs without tipping the device. Then look again.

Condensation Real leak
Appearance Thin, watery, clear or faintly tinted Thicker, carries the colour of your liquid
Amount A few small droplets A visible pool, or a steady film that returns
Timing Builds slowly over hours Appears within minutes, even when idle
Sound Nothing unusual Gurgling on the draw

Condensation is normal. Vapour cools inside the airway and a little of it settles as liquid — every pod device does this. Wipe it out once a day and forget about it. If what you’re seeing matches the right column, work down this list.

1. You’re overfilling it

The fill line isn’t decorative. Liquid expands when it warms up, and if there’s no air gap left at the top, that expansion has to go somewhere — usually out through the coil and down the airway.

Fill to about 80% and leave the top fifth clear. If your pod has a visible fill line, respect it; if it doesn’t, leave a gap roughly the height of your fingernail.

2. The fill port gasket isn’t seated

This is the single most common cause of sudden, heavy leaking, and it usually happens right after a refill.

The rubber plug that seals the fill hole has to sit completely flush. A bottle nozzle pushed in at an angle can lift the edge of the gasket, or leave it folded under. Run a fingernail around the seal — if any part of it sits proud of the surface, press it back down flat and check that the plug clicks into place.

3. The pod isn’t pushed all the way in

Pods seat with a firm push, often with an audible click. Half-seated, the seals don’t engage and liquid finds the gap. Take the pod out, look at the contacts, and push it back in until it stops — not gently, but not with force either.

4. Pressure changes

Air pressure inside the pod has to stay balanced with the outside. Change the outside pressure quickly and the liquid gets pushed out through the wick.

  • Flying. Cabin pressure drops; pods leak. Keep the pod half full, upright, and ideally remove it from the device.
  • Temperature swings. A device left in a hot car, then brought into air conditioning, will leak.
  • Altitude. Driving into mountains does the same thing, more slowly.

5. The liquid is too thin

High-PG liquids (70% PG and above) are runny. In a pod designed for 50/50, they wick so fast that the coil floods — liquid passes straight through instead of vaporising, and it ends up in the base.

The giveaway: leaking plus a gurgling draw plus weak, spitty vapour. If your liquid is thin and the weather is warm, it gets worse still, because heat thins it further.

6. You’re drawing too hard

A pod coil produces a limited amount of vapour per second. Pull harder than that and you’re not getting more vapour — you’re sucking liquid up the airway before it can be vaporised.

Pod devices are mouth-to-lung: draw gently into your mouth for three or four seconds, then inhale. If you’re pulling like you’re drinking a thick milkshake, that’s the problem.

7. A worn O-ring or a cracked pod

Every pod has small silicone seals at the base. They compress with heat cycles and eventually stop sealing. Plastic pods also develop hairline cracks at the seam, usually invisible until you squeeze them gently and watch for a wet line.

If a pod has been in use for three weeks or more and starts leaking for no obvious reason, this is the likely answer — and it isn’t fixable. Replace the pod.

The five-minute fix

  1. Remove the pod and dry both sets of contacts with a tissue
  2. Check the fill gasket sits flush all the way around
  3. Look for cracks at the pod seam — squeeze gently and watch for moisture
  4. Refill to 80%, not to the brim
  5. Seat the pod firmly, wait ten minutes, then vape gently

If it’s still leaking after that, the pod is the problem, not your technique. Replace it.

Three things not to do

  • Don’t blow hard into the mouthpiece. It’s the most common “fix” people try, and it pushes liquid straight into the airflow sensor — which can kill an auto-draw device permanently.
  • Don’t use compressed air. Same damage, faster.
  • Don’t store the device upside down or on its side overnight. Gravity does the rest.

When to stop troubleshooting

If a pod leaks within minutes of filling, twice in a row, with a gasket that’s seated correctly — it’s defective. Contact us with your order number; leaking-on-arrival pods are covered.

And if you’re buying replacement pods anyway, check the compatibility table first. A pod that’s the wrong resistance for your device runs hotter than it should, which accelerates exactly the seal wear that causes leaking.

Need the pods for this?

Shipped from Rotterdam. Order before 15:00 CET for same-day dispatch.

Shop now

Read next

Troubleshooting

Pod Not Firing? Work Through These 7 Checks in Order

You press the button, or take a draw, and nothing happens. No vapour, no crackle, maybe a light…

November 19, 2026 · 5 min read
Troubleshooting

Why Your Vape Tastes Burnt — and 6 Fixes That Actually Work

Burnt taste from a new pod is almost never a faulty coil. Here are the six real causes,…

November 19, 2026 · 5 min read